GCSE physics required practicals become much easier to revise when every investigation is reduced to the same repeatable process. This guide gives you a master checklist, a board-aware practical map, data-record templates, worked examples and an exam-focused workflow for planning, carrying out, analysing and evaluating practical physics.
Overview
A required practical is not only a method to memorise. You may be assessed on identifying variables, choosing suitable equipment, recording measurements, plotting or interpreting graphs, explaining patterns and evaluating limitations. A strong practical write-up therefore shows both what you did and why the method produced useful evidence.
The exact list and wording differ between AQA, Pearson Edexcel and OCR specifications, and specifications can be revised. Use the table below as a revision cross-reference rather than as a replacement for your current specification or teacher’s practical list.
| Practical family | AQA | Edexcel | OCR | Typical purpose |
|---|---|---|---|---|
| Density | Check specification | Check specification | Check specification | Determine density from mass and volume |
| Specific heat capacity | Check specification | Check specification | Check specification | Investigate energy required to raise temperature |
| Thermal insulation | Check specification | Check specification | Check specification | Compare cooling or heating under controlled conditions |
| Resistance and I–V characteristics | Check specification | Check specification | Check specification | Relate potential difference, current and resistance |
| Force, extension and springs | Check specification | Check specification | Check specification | Measure extension as load changes |
| Motion and acceleration | Check specification | Check specification | Check specification | Measure how motion changes with force or mass |
| Waves and light | Check specification | Check specification | Check specification | Measure wavelength, frequency, refraction or wave speed |
| Radiation | Check specification | Check specification | Check specification | Investigate absorption, count rate or shielding |
Master checklist: know the purpose; identify the independent, dependent and control variables; draw or recognise the apparatus; explain the safe procedure; record units and resolutions; repeat readings; calculate a mean where appropriate; plot a correctly labelled graph; describe the relationship; estimate uncertainty; identify limitations; and suggest a specific improvement.
How to estimate
In practical physics, “estimate” usually means making a justified judgement from measurements rather than pretending that an answer is exact. A repeatable approach is:
- Estimate the expected scale. Before measuring, decide whether the quantity should be a few millimetres, several centimetres, a fraction of an ampere or a temperature change of a few degrees. This helps expose misplaced decimal points and unsuitable equipment.
- Use the instrument resolution. If a ruler has millimetre divisions, record length in a way that reflects that resolution. Do not write extra digits that the instrument cannot support.
- Repeat measurements. Take at least three readings where time and equipment allow. Look for an anomalous result, but do not delete it simply because it is inconvenient. Record a reason for excluding a value, if exclusion is justified.
- Calculate consistently. Show substitutions, retain sensible significant figures and include units. For density, for example, use density = mass ÷ volume, with mass and volume in compatible units.
- Compare with the pattern, not just one point. A conclusion should use the trend in the results. A best-fit line, gradient or percentage change may be more informative than comparing two individual readings.
For uncertainty, begin with the simplest appropriate estimate: the resolution of a single instrument, or twice the resolution when a length is found from two ruler positions. For a repeated set, compare the spread of readings with the instrument uncertainty. Keep the method consistent with the level expected by your course and teacher.
Reusable data-record template
Title and purpose: Independent variable and range: Dependent variable and unit: Control variables: Equipment and resolution: Safety precaution: | Independent variable | Trial 1 | Trial 2 | Trial 3 | Mean | Dependent-unit | |----------------------|---------|---------|---------|------|----------------| | | | | | | | Anomalous result and reason, if applicable: Graph type and axis scales: Relationship observed: Main uncertainty: Improvement:
Complete the table during the investigation, not from memory afterwards. Include a heading for every quantity and unit. A blank table with no units is a common avoidable weakness in a practical write-up.
Inputs and assumptions
Before starting, write down the inputs that determine whether the investigation is fair and repeatable:
- Independent variable: the quantity deliberately changed, such as load, length, voltage or distance.
- Dependent variable: the quantity measured, such as extension, current, temperature or time.
- Control variables: conditions kept constant, such as material, wire thickness, starting temperature, light level or total mass.
- Range and intervals: choose enough values to reveal a pattern without exceeding the safe operating range of the apparatus.
- Equipment limits: note the smallest scale division, meter range, thermometer resolution or timing method.
- Safety assumptions: identify hot surfaces, electrical currents, falling masses, sharp edges, bright light or radioactive sources where relevant. Follow your school’s risk assessment and teacher instructions.
Use cautious language when the data are limited. “The results suggest a linear relationship within the measured range” is stronger scientifically than “the variables are always directly proportional”. Direct proportionality requires a suitable graph and evidence that the line passes through the origin, within experimental uncertainty.
Worked examples
Example 1: density of a regular solid
Purpose: determine density by measuring mass and volume. Apparatus: balance, ruler and regular solid. Measure the relevant dimensions in metres or centimetres, calculate volume using the correct geometric formula, then divide mass by volume.
Method summary: zero or check the balance, measure each dimension more than once, calculate the volume, measure mass and repeat if possible. Avoid reporting volume with more precision than the dimensions justify.
Example conclusion: “The calculated density was approximately ___ unit. Repeated dimension measurements gave similar values, so random uncertainty was reduced. The main limitation was the ruler resolution and the possibility of measuring an edge at an angle.”
A useful improvement is to measure the dimensions at several positions and use mean values. If the object is irregular, do not force the regular-solid method onto it; use water displacement with suitable care to avoid trapped air and splashing.
Example 2: resistance of a wire
Purpose: investigate how resistance depends on wire length. Apparatus: power supply, ammeter, voltmeter, switch, connecting leads and resistance wire. Change only the length of wire in the circuit, measure current and potential difference, and calculate resistance using R = V ÷ I.
Keep the current low or switch off between readings so that heating does not change the wire’s resistance. Record the wire length, potential difference and current in a table. Plot resistance against length if that is the chosen analysis. A straight-line trend supports the conclusion that resistance increases with length over the investigated range.
Mark-winning evaluation phrase: “Heating is a systematic limitation because the wire temperature may increase as current flows, changing resistance. Taking readings quickly, using a lower current and opening the switch between readings would reduce this effect.” This is more useful than simply writing “take more care”.
Example 3: force and extension
Measure the spring’s original length, add loads one at a time and record the new length. Calculate extension as new length − original length. Use a pointer and a fixed scale where possible to reduce parallax. Repeat readings and plot force against extension. The graph may be linear only up to the limit of proportionality; do not extend the conclusion beyond the data.
When to recalculate
Revisit your practical checklist whenever your exam board publishes a specification revision, your school changes its practical sequence or you begin a new past-paper season. The official required-practical list, terminology and assessment emphasis should always be checked against the current board materials rather than an old revision guide.
Recalculate your analysis when you correct a unit, replace an anomalous result with a documented justification, collect more repeats, change the graph scale or discover that a control variable was not controlled. Keep the original data: an audit trail lets you explain why a conclusion changed.
For each practice session, score yourself against five questions: Did I identify the variables? Did I choose a valid range? Did I record units and repeats? Did I use the graph or calculation correctly? Did my evaluation name a specific limitation and improvement? Log the recurring error and repeat the same practical after a short interval. This creates a practical revision tracker instead of a one-off write-up.
For further analysis support, see Physics Practical Data Analysis: Uncertainty, Best-Fit Lines and Evaluation Templates and GCSE Physics Required Practicals: Methods, Variables, Results Tables and Evaluation Checklist. Keep this page alongside your current specification and update the board mapping whenever the specification or school practical programme changes.