A suitable physics practical risk assessment identifies what could cause harm, who could be affected, and how the risk will be controlled before students use the equipment. This teacher-ready guide provides a repeatable workflow, a hazard reference table, student-friendly wording, and review checkpoints for GCSE and A-Level practical work. Use it alongside your school or college procedures, equipment instructions and any required specialist guidance; it is not a substitute for local approval by a competent person.
Overview
A risk assessment should be specific to the activity, apparatus, room and group of students. “Physics practical” is too broad to assess safely: a low-voltage circuit, a ray box investigation, a ripple-tank demonstration and a radioactive-source experiment have different hazards and controls.
A useful assessment normally records:
- the practical title, date, class and supervising staff;
- the equipment, materials and quantities being used;
- foreseeable hazards, including misuse and foreseeable equipment failure;
- who may be harmed, such as students, teachers, technicians or visitors;
- control measures, including personal protective equipment where appropriate;
- supervision, emergency arrangements and disposal requirements;
- the person responsible for checking the controls; and
- the review date and any changes made after the lesson.
Separate a hazard from a risk. A hot soldering iron is a hazard; the possibility that a student touches it and receives a burn is the associated risk. Controls should reduce the likelihood or severity of harm. They might include using a lower temperature, replacing a damaged lead, restricting access, giving a clear demonstration, or changing the practical method.
For exam-board practical work, safety should support the intended learning rather than replace it. If a required practical is adapted, record why the change is needed and check that students can still collect and evaluate the relevant evidence. A practical write-up should not encourage students to repeat an unsafe procedure simply because it appears in an old worksheet.
What to track
Begin with a walk-through of the practical as it will actually happen. Consider setup, student use, movement around the room, clearing away and disposal. The table below is a starting point, not a complete assessment for every apparatus model.
| Equipment or activity | Possible hazard | Typical controls and supervision | Suitable student wording |
|---|---|---|---|
| Power supplies, cells and circuit leads | Short circuits, hot wires, damaged insulation or electric shock from unsuitable equipment | Use the intended low-voltage supply; inspect leads; switch off before changing connections; prevent contact with mains electricity; supervise fault-finding. | “Switch off the supply before changing the circuit. Report damaged leads or hot components immediately.” |
| Lamps, heaters and resistance-wire investigations | Hot surfaces, burns, melting insulation or fire if equipment is left energised | Use heat-resistant supports where needed; keep combustible materials away; allow cooling time; switch off between readings and at the end. | “Do not touch the lamp or wire until it has cooled. Use tongs or the stated handling method.” |
| Masses, clamps and falling objects | Falling masses, unstable stands, trapped fingers or swinging apparatus | Place stands on a stable bench; secure clamps; keep feet and hands clear; limit the drop distance; check the release area before loading. | “Keep clear of the falling mass and do not place hands beneath suspended equipment.” |
| Glassware, lenses and prisms | Breakage, sharp edges or cuts | Check for cracks; carry glass with two hands when appropriate; keep it away from bench edges; report breakage and do not pick up fragments by hand. | “Tell the teacher if glass breaks. Do not touch fragments; follow the laboratory clean-up instructions.” |
| Ray boxes, bright lamps and optical investigations | Glare, heat or eye discomfort | Avoid directing intense light into eyes; use the lowest suitable setting; allow hot lamps to cool; provide clear viewing positions. | “Never look directly into the bright source. Keep the beam directed at the apparatus.” |
| Lasers | Eye injury from direct or reflected beams | Use only an approved, labelled device under local rules; keep the beam below or above eye level as appropriate; remove reflective objects; never point it at people; restrict alignment and switching-on to trained users. | “Never look into the beam or aim it at anyone. Keep reflective objects away from the beam path.” |
| Sound, vibration and signal generators | Excessive sound levels, trailing leads or equipment falling from a bench | Use a reasonable output; keep speakers stable; route leads safely; stop if discomfort occurs; supervise demonstrations involving high output. | “Tell the teacher if the sound is uncomfortable. Do not increase the output without permission.” |
| Liquids, chemicals or thermal fluids | Splashes, skin or eye irritation, spills and unsafe disposal | Check the substance-specific instructions and school chemical procedures; use the smallest practical quantity; wear required eye protection; label containers; arrange suitable waste disposal. | “Wear the stated eye protection and report spills immediately. Do not pour waste into a sink unless instructed.” |
| Radioactive sources or sealed sources | Unnecessary exposure, loss of a source or incorrect handling | Follow the institution’s specialist arrangements; use the minimum exposure time and greatest practical distance; keep sources secured and accounted for; restrict handling to authorised, trained staff or students under direct supervision. | “Follow the source-handling instructions exactly and report any missing or misplaced item at once.” |
Electrical and laser controls deserve particular care because “low power” or “classroom use” does not remove the need for an equipment check. For chemicals, radioactive sources and any specialist apparatus, use the relevant local documentation and seek advice from the responsible technician or safety lead rather than relying on a generic online template.
Planning template
Practical: [title and class] Date: [date] Supervisor: [name]
Method and equipment: [brief description, including quantities, power sources and specialist items]
Hazard: [what could cause harm] Who may be affected: [students, staff, visitors]
Controls: [equipment checks, layout, instructions, supervision, protective equipment and emergency actions]
Disposal and end-of-lesson checks: [waste route, cooling, isolation, storage and room inspection]
Approval and review: [responsible person, date checked and changes required]
Cadence and checkpoints
Use three checkpoints rather than treating the risk assessment as a document completed once and forgotten.
- Before the lesson: compare the planned method with the actual equipment. Check leads, plugs, stands, glassware, batteries, lasers, chemicals and emergency equipment. Note changes in room layout, class size, student needs or supervision. Test the setup without students where a fault could create a hazard.
- At the start: explain the few controls students must remember, demonstrate any dangerous or unfamiliar step, identify stop signals and confirm how to report a spill, breakage, burn, electric fault or near miss. Do not assume that a previous class understood the same instruction.
- After the lesson: record defects, unexpected behaviour, spills, equipment overheating, repeated unsafe actions and near misses. A near miss is useful evidence that a control may be weak, even when nobody was injured.
For recurring practicals, keep a simple equipment and incident log. A monthly or half-termly check can identify patterns such as one type of lead repeatedly failing, students crowding around a demonstration, or a particular stand becoming unstable. A formal review at the start of each academic year is sensible, followed by a check whenever the method, apparatus, room or relevant specification changes.
How to interpret changes
A changed result is not automatically a safety problem, but an unexpected result should prompt a pause before students repeat the method. Ask four questions:
- Did the apparatus behave as expected, or was there overheating, sparking, cracking, leakage or unusual movement?
- Did students follow the stated controls, and were those controls clear enough?
- Has the equipment, quantity, power setting, room layout or group supervision changed?
- Would repeating the step expose anyone to greater harm?
If the answer suggests increased risk, stop the activity, isolate equipment where appropriate and seek technical or local safety advice. Do not improvise a replacement control during a live lesson unless it has been judged suitable. A safer modification might be reducing the energy supplied, increasing distance, using a demonstration instead of group work, replacing damaged apparatus, or removing a step entirely.
Keep the language measurable. “Be careful with electricity” is weak; “switch off the supply before changing connections and report hot wires” tells students what to do. Likewise, “wear safety equipment” should identify the equipment and the task that requires it. Link the control to the hazard so that students understand its purpose.
When to revisit
Revisit the assessment before every practical, even when the activity is familiar. Make an immediate update after an incident, near miss, equipment failure, change of method or change in the class’s supervision needs. Review recurring activities monthly or termly according to how often they are used, and complete a broader review at the start of each academic year.
Use this short end-of-lesson checklist:
- Record any incident, near miss or unexpected equipment behaviour.
- Mark which control worked and which was unclear, impractical or missed.
- Check that damaged or suspect equipment is removed from use and reported through the local process.
- Update the method, student wording, supervision level or disposal instruction.
- Before the next class, brief the technician and supervising staff on the change.
Teachers planning broader practical sequences may also find it useful to compare this checklist with a physics lesson resource planning guide, a GCSE required practical checklist and a practical graphs and evaluation template. The goal is not to create paperwork for its own sake: it is to make each practical safer, clearer and easier to improve the next time it is taught.