A-Level Physics Required Practicals: Complete Method, Variables, Uncertainty and Evaluation Guide
A-Level PhysicsRequired PracticalsExperimental SkillsUncertaintyPractical Write-Up

A-Level Physics Required Practicals: Complete Method, Variables, Uncertainty and Evaluation Guide

PPhysics Plus Editorial Team
2026-11-03
8 min read

A reusable A-Level Physics required practicals checklist covering methods, variables, uncertainty, graphs, safety and evaluation.

A-Level Physics required practicals are assessed through the decisions you make, not just the apparatus you remember. This guide gives you a reusable checklist for planning methods, identifying variables, recording data, handling uncertainty, evaluating results and answering practical questions across AQA, Edexcel and OCR-style courses. Always compare the checklist with your own specification and teacher guidance, because the named practicals and assessment wording can vary.

Overview

A strong practical answer explains how reliable evidence will be produced. In an exam, listing equipment is rarely enough. You need to show that you understand what is being changed, what is being measured, what must be controlled and how the measurements will support a conclusion.

For every A-Level Physics practical, revise these eight elements:

  1. Aim: state the physical relationship or quantity being investigated.
  2. Apparatus: name equipment precisely, including a suitable measuring instrument and its resolution where relevant.
  3. Variables: identify the independent, dependent and control variables.
  4. Method: describe a safe, repeatable sequence of steps.
  5. Data: include units, sensible ranges, repeats and a clear table.
  6. Analysis: select an appropriate graph, gradient, intercept or calculation.
  7. Uncertainty: estimate or calculate the uncertainty in measurements and derived quantities.
  8. Evaluation: identify limitations and propose improvements that address those limitations.

Keep your practical notes separate from a purely descriptive summary. For example, “measure the extension” is incomplete unless you explain what load is applied, how the original length is established, how parallax is avoided and whether the object is allowed to return to its starting point between readings.

For broader support, use this required practical physics write-up checklist alongside your own laboratory notes. It can also help to revise practical definitions with the A-Level Physics required definitions guide.

Checklist by scenario

1. Mechanics and materials practicals

Typical investigations include motion, collisions, moments, springs or the behaviour of a material. Begin by deciding exactly what is measured: displacement, time, velocity, force, extension, diameter or another quantity.

  • Use a fixed reference point and explain how distances are measured consistently.
  • For timing experiments, repeat measurements and consider measuring several cycles or a longer distance to reduce the percentage effect of reaction time.
  • For a spring or wire, record the original length before adding loads and do not exceed a safe elastic limit.
  • Take readings over a useful range rather than clustering all values together.
  • In a force–extension investigation, consider whether the graph should pass through the origin and whether the relationship remains proportional.
  • For moments, measure perpendicular distances from the pivot and reduce friction or movement at the pivot where possible.

When evaluating a mechanics method, avoid saying only “human error”. Name the mechanism: reaction time, parallax, friction, vibration, an unsteady release or a changing angle. Then match the improvement to it, such as using light gates, a fiducial marker, a video analysis method or a more stable support.

2. Electricity and circuit practicals

For resistance, resistivity, internal resistance or component characteristics, draw or describe the circuit clearly before taking readings.

  • Check the polarity and range of meters before connecting the circuit.
  • State whether the ammeter is in series and the voltmeter is in parallel.
  • Record current and potential difference together, with units and consistent significant figures.
  • Limit heating by using a switch, taking readings promptly or allowing the component to cool between readings.
  • Use a range of currents or voltages that shows the behaviour being investigated without damaging the component.
  • For a wire, measure length and diameter carefully and take diameter readings at several positions if appropriate.

Temperature is a frequent control variable in electricity practicals. If resistance changes as the component heats, a result may reflect temperature rather than the intended independent variable. An improvement should therefore control or monitor temperature, not simply repeat the same measurement.

3. Waves, optics and resonance practicals

Wave investigations often involve measuring wavelength, frequency, distance, angle, intensity or a resonant length. The method should make the reference points unambiguous.

  • Measure across several wavelengths where possible and divide by the number of intervals.
  • Keep the source, detector and alignment fixed while changing the chosen independent variable.
  • For refraction, measure angles from the normal, not from the surface.
  • For resonance, define how the maximum response is identified and repeat readings near the peak.
  • Use a graph that linearises the relationship when this gives a clearer test of a model.
  • Reduce parallax by viewing scales directly or using a projected image or fiducial line.

If a graph contains a maximum or minimum, explain how its position was found. A single visual estimate may be less reliable than taking additional readings around the turning point and fitting a smooth curve or using a suitable analysis method.

4. Thermal, radiation and data-logging practicals

For heating and cooling, specify how energy transfer is measured and identify sources of unwanted energy loss. Insulation, a lid, a draught shield or a temperature sensor may improve consistency, but the chosen improvement must address a stated limitation.

For radiation work, follow the laboratory’s safety instructions and distinguish background counts from the count due to the source. Take repeated counts over a defined time, keep the source–detector geometry fixed and describe how background is accounted for. Do not suggest handling radioactive sources differently from the approved procedure.

Data loggers can increase sampling speed and produce more readings, but they do not automatically remove systematic error. Check the sensor range, sampling interval, calibration, zero reading and whether the sensor responds quickly enough for the changing quantity.

What to double-check

Variables and controls

Write one clear sentence for each variable. The independent variable is deliberately changed; the dependent variable is measured; control variables are kept constant because they could affect the dependent variable. “Use the same equipment” is not always enough. Name the relevant property, such as wire length, cross-sectional area, temperature, mass, angle, supply voltage or distance.

Tables and units

Put the quantity and unit in the column heading, for example length / m or current / A, rather than repeating units inconsistently in every cell. Use a sensible number of decimal places based on the instrument. Do not report calculated values to much greater precision than the measurements justify.

Uncertainty and percentage uncertainty

Uncertainty describes the range within which a measured value is expected to lie. For a single analogue reading, the instrument resolution and the way the scale is read may both matter. For repeated readings, use the spread of results as evidence of random variation.

A useful calculation is:

percentage uncertainty = (absolute uncertainty ÷ measured value) × 100

For quantities combined by multiplication or division, percentage uncertainties are commonly added as an estimate. For addition or subtraction, absolute uncertainties are commonly added. Apply the convention taught by your exam board and show enough working to make your approach clear.

Ask whether the uncertainty is large enough to affect the conclusion. If two results overlap within their uncertainties, claiming a definite difference may not be justified.

Graphs and gradients

Plot the independent variable on the horizontal axis and the dependent variable on the vertical axis unless the investigation requires a transformed graph. Label both axes with quantities and units, use a sensible scale, plot points accurately and draw a single best-fit line or curve where appropriate.

A gradient should be calculated using two widely separated points on the best-fit line, not two adjacent raw data points. If uncertainty in the gradient is required, consider drawing suitable maximum- and minimum-gradient lines and explaining how they were selected.

Evaluation and improvements

A strong evaluation has three parts: limitation, effect and improvement. For example: “Heat loss to the surroundings may reduce the measured temperature rise, making the calculated energy transfer too small. Use insulation and a lid, while recording the initial and final temperatures promptly.” This is stronger than “improve the apparatus”.

Common mistakes

  • Confusing accuracy and precision: repeated close readings can be precise but systematically wrong if the instrument is not calibrated.
  • Calling every issue random error: a zero error, calibration error or consistent heat loss may create a systematic effect.
  • Using repeats incorrectly: repeats help identify scatter, but repeating the same biased method does not remove systematic error.
  • Giving generic improvements: an improvement must directly address a named limitation and remain practical.
  • Ignoring units in equations: convert values consistently before using physics formulas.
  • Overstating a conclusion: compare the trend with the uncertainty and state whether the evidence supports, partly supports or does not support the model.
  • Forgetting safety: mention relevant risks, such as hot surfaces, electrical current, trailing wires, falling masses, lasers or radiation, together with a reasonable control.
  • Memorising a method without understanding it: exam questions may alter the apparatus or ask you to adapt the procedure.

Practise adapting methods rather than copying them. For example, take a familiar force–extension investigation and ask how you would change it to measure energy, reduce percentage uncertainty or test a different material.

When to revisit

Return to this checklist at four useful points:

  1. Before carrying out a practical: check the aim, variables, apparatus, safety controls and data table.
  2. After the practical: complete the graph, uncertainty estimate, conclusion and evaluation while the method is still clear.
  3. Before practical exam questions: practise planning an unfamiliar investigation from a short prompt, including a control variable and a measurable improvement.
  4. Before final revision: compare your notes with the current AQA, Edexcel or OCR specification and your school’s required practical list. Exam-board wording and practical coverage can change, so your specification remains the final reference.

For a quick self-check, choose one practical and answer these questions without looking at your notes: What is being changed? What is measured? What must stay constant? How will uncertainty be reduced? Which graph tests the relationship? What limitation could affect the conclusion? If you can answer all six precisely, you are revising the experimental reasoning that practical questions are designed to test, not just recalling a sequence of steps.

Related Topics

#A-Level Physics#Required Practicals#Experimental Skills#Uncertainty#Practical Write-Up
P

Physics Plus Editorial Team

Physics Education Editors

Senior editor and content strategist. Writing about technology, design, and the future of digital media. Follow along for deep dives into the industry's moving parts.